Categories
Writers Solution

When comparing samples of bituminous coal (56) and anthracite coal (75), use the streak plate and wire nail to test for differences in streak color and hardness

Coal supplies 2/5 of the world’s electricity demands. Coal is often called a “fossil fuel” because it was formed from the remains of vegetation up to 400 million years old. As trees and plants died in forested swamps, they sank and accumulated in an anoxic environment (like the modern Okefenokee Swamp of Georgia). The decaying plants were subsequently buried by silt, sand, and other matter as the depositional environment changed slowly over time. There are four stages in coal formation: peat, lignite, bituminous, and anthracite. The stage depends on the conditions to which the plant remains are subjected after burial; the higher the pressure (and heat), the higher the rank of coal. High-ranking coal (i.e., anthracite) is denser and contains less moisture and gases than low-ranking coal (i.e., bituminous).

  1. When comparing samples of bituminous coal (56) and anthracite coal (75), use the streak plate and wire nail to test for differences in streak color and hardness. Compare sample luster. In what ways are these samples different? In what ways are they similar?
  2. Figure 2 shows where coal is currently found in Pennsylvania. According to the principles of original horizontality and lateral continuity, coal deposits once covered this entire region. Why does the map show ‘breaks’ – areas where no coal is found – in the coalfields? *consider the structural geology of the areas depicted in Figure 1)
  3. a. In what physiographic province are the anthracite coalfields located? (see Figure 3). ____________________________________________________________________________________                   b. In what physiographic province is the main bituminous coalfield located? (see Figure 3). 
  4. a. Refer to Figure 4 *In the Explanation Section*. What are the ages of the rocks in Schuylkill County, east-central Pennsylvania? _____________________________________________________________                                                       b. Refer to Figure 4 *In the Explanation Section*. What are the ages of the rocks in Clearfield County, central Pennsylvania? 
  5. a. What is the age of the coal in Schuylkill County?  _____________________________________         b. What is the age of the coal in Clearfield County?  _____________________________________  
  6. Review your answers to questions 3-5. Summarize the similarities and discuss the different geological processes that controlled the distribution of anthracite versus bituminous coal in Pennsylvania.
  7. Consider the bedrock patterns in Figure 1 and Figure 4. Sketch a generic cross section through the main bituminous coalfield to show how it is structurally different from the anthracite fields

GET SOLUTION FOR THIS ASSIGNMENT

CLICK HERE TO MAKE YOUR ORDER

TO BE RE-WRITTEN FROM THE SCRATCH

NO PLAGIARISM

  • Original and non-plagiarized custom papers- Our writers develop their writing from scratch unless you request them to rewrite, edit or proofread your paper.
  • Timely Deliverycapitalessaywriting.com believes in beating the deadlines that our customers have imposed because we understand how important it is.
  • Customer satisfaction- Customer satisfaction. We have an outstanding customer care team that is always ready and willing to listen to you, collect your instructions and make sure that your custom writing needs are satisfied
  • Confidential- It’s secure to place an order at capitalessaywriting.com We won’t reveal your private information to anyone else.
  • Writing services provided by experts- Looking for expert essay writers, thesis and dissertation writers, personal statement writers, or writers to provide any other kind of custom writing service?
  • Enjoy Please Note-You have come to the most reliable academic writing site that will sort all assignments that that you could be having. We write essays, research papers, term papers, research proposals. When comparing samples of bituminous coal (56) and anthracite coal (75)

Get Professionally Written Papers From The Writing Experts 

Green Order Now Button PNG Image | Transparent PNG Free Download on SeekPNG Our Zero Plagiarism Policy | New Essays
Categories
Writers Solution

Prediction of beam and plate section dimensions

The design is about the design of floor;
please follow the (Example1 pdf) step by step which attached in below and complete the design.
3.3 Design examples
3.3.1 Layout of floor structure
The plane arrangement of the floor structure is shown in Fig. 3-8, the main beam is arranged along the longitudinal and transverse direction, and the secondary beam is arranged along the longitudinal direction, and two secondary beams are arranged in each span of the main beam. The span of transverse main beam is 7.2 m, that of longitudinal main beam is 6.6 m , that of secondary beam is 6.6 m, the span of the board is 2.4m. Because of 6600/2400=2.75 2, it is necessary to calculate according to the requirements of the code, and when calculated according to the unidirectional plate, a sufficient number of structural tendons should be arranged along the long side direction. This example is calculated as an one-way plate and takes the necessary construction measures.
Fig. 3-8 layout of floor structure
3.3.2 Prediction of beam and plate section dimensions
? slab thickness: according to«Concrete specification», the thickness of the slab can be obtained according to Table 3-2, which takes into account the durability of the floor and the minimum thickness 70mm of the industrial building considering the durability of the floor and the minimum thickness of the floor of the industrial building. The thickness of the slab is h= 80mm, taking into account the durability of the floor and the minimum thickness of the floor of the industrial building.
? the section size of the beam can be determined according to experience. According to the minimum stiffness requirements of deflection and crack width without checking, the size of beam loading surface is estimated according to Table 3-1. Main beam:
Secondary beam:
3.3.3 Design of boards

  1. Load calculation
    1) Standard value of constant load
    30m thick tile floor (including cement mortar): 0.65 (kN/m2).
    20mm thick cement mortar leveling layer: 20×0.02 = 0.4 (kN/m2).
    80mm thick reinforced concrete slab: 25×0.08 = 2.00 (kN/m2).
    20 mm thick mixed mortar surface: 17×0. 02 =0.34 (kN/m2).
    Constant load standard value: gk = 3.39 kN/m2.
    2) Standard value of live load
    Live load standard value: gk = 8.00 kN/m2.
    According to Appendix D, Table D.1-1. In the four types of metalworking workshops, the span of the plate is 2.4 m and 2.0 m. The standard value of live load is 800kN/m2 and the coefficient of combined value is ?c =1.0 3) load design value
    According to Appendix D, Table D.1-1. The combination coefficient of the live load ?c =1.0, the standard value of the live load qk = 8.00kN/m2 4.0 kN/m2, and the partial coefficient is 1.3. The design value of the load effect is calculated according to formula (3-1) and formula (3-2) for variable load effect and permanent load effect control, Take the maximum value. Variable load effect control combination:
    Combination of permanent load effect control:
    It is found from the calculation that the load design value obtained by the combination of permanent load effect control is large, and the internal force of the plate is calculated by g+q=14.98 kN/m2.
  2. Calculation diagram
    In this project, the two ends of the plate are connected with the beam as a whole, and the calculated span of the plate is calculated according to Table 3-3, as follows.
    The difference of each calculated span is less than 10%, which can be approximately calculated according to the equal span continuous plate. The span 2200mm of the plate and the plate and strip of the plate width b=1000mm are calculated. The calculation diagram is shown in figure 3-9.
    Fig. 3-9 board calculation diagram
  3. Calculation of bending moment and reinforcement of Plate
    1) Bending moment calculation
    According to the Code of Internal Force redistribution, the bending moment design values of equal span continuous unidirectional plates subjected to uniform load are calculated according to formula (3-6), and the bending moment coefficients are determined in Table 3-4 of ?mb.
    According to the rules of Internal Force redistribution, when the perimeter of unidirectional continuous slab is connected with reinforced concrete beam as a whole, the design value of span center and bearing bending moment of each middle span can be reduced by 20%, so the values of M2, M3 and Mc can be reduced by 20%, except for the second support of edge span and off end, and the results after reduction are shown in Table 3-7.
    2) Calculation of plate reinforcement
  4. Plate reinforcement diagram (figure 3-10)
    In general, the dynamic load on the floor is not large, so the separated reinforcement can be used.
    Table 3-7 Reinforcement calculation diagram of slab
    Figure 3-10 Plate reinforcement diagram
    3.3.4 Design of secondary beams 1. Load calculation
    1) Standard value of constant load
    Constant load from the plate: 3.39×2.4 = 8.14 (kN/ m).
    The weight of the secondary beam is 25×0.2× (0.5-0.008) = 2.12 (kN/m).
    Beam side plastering: 17×0.02× (0.5-0.008) ×2 = 0.29 (kN/ m).
    Load standard value: gk = 10.53 (kN/ m).
    2) Standard value of live load
    According to Table D.0.1-1 in Appendix D to the load Code, the distance between the secondary beams is 2.4m 2.0m, the standard value of live load is 6.00kN/m2, and the coefficient of combination value is 1.0.The standard value of live load is 6.00kN/m2.
    The standard value of live load from the plate is qk = 7×2.4 = 14.40 (kN/m).
    3) load design value
    According to table D.0.1-1 in Appendix D to the load Code, the combined value coefficient of live load is ?c =1.0, the standard value of live load is qk = 6.00kN/m2 4.0 kN/m2, and the score coefficient is 1.3. The design values of load effect are calculated according to the variable load effect and permanent load effect of formula (3-1) and formula (3-2), respectively, and the larger values are taken.
    Permanent load effect: g+q= 1.2×10.53+1.3×14.40×1.0=31.36 (kN/ m2)
    Variable load effect: g+q= 1.35×10.53+1.3×14.40×1.0=32.94 (kN/ m2)
    According to the calculation, the design value of the combined load controlled by the permanent load effect is large, and the internal force of the secondary beam is calculated by g+q=32.94kN/m. 2. Calculated span
    The calculation method of the calculation span is the same as that of the plate, which is calculated according to Table 3-3, as follows.
    Middle span: l0=ln = 6600-300 = 6300 (mm)
    Edge span: l0=ln =6600-100-150 = 6350 (mm)
    The difference between the calculated span of the side span and the middle span is 63506300/6300=0.79% 10%, so the internal force can be calculated according to the equal span continuous beam. The geometric size and calculation diagram of the secondary beam are shown in figure 3-11.
    Fig. 3-11 Calculation diagram of secondary beam
  5. Internal force calculation of secondary beam
    The calculation method of internal force of secondary beam is the same as that of unidirectional plate. According to the Code of Internal Force redistribution, the bending moment design values of equal span continuous unidirectional plates subjected to uniform load are calculated according to formula (3-6), and the bending moment coefficients are determined in Table 3-4 of ?mb. 1) Design value of bending moment
    2) Shear design value
    3) Reinforcement calculation of secondary beam section
    The secondary beam and the slab are integrally cast, so the secondary beam support is calculated as a rectangular section, and the mid-span section is calculated as a T-shaped section. Calculate the width bf of the flange of the T-shaped section according to Article 4.1.5 of the -Concrete Code-, and the side span and the middle span are calculated according to the minimum value of l0/3 and (b+Sn).
    Take bf =-2.10m, effective section height h0 =500-40= 460(mm), flange thickness hf = 80mm,
    This value is greater than the mid-span bending moment design value M1, M2, M3, so the midspan section of each span belongs to the first type of T-shaped section. The calculation parameters are as follows. C30 concrete: fc= 14.3MPa; reinforcement: longitudinal reinforcement fy = 360MPa (HRB400), stirrup fyv =270MPa (HPB300), the calculation results of the flexural bearing capacity of the normal section of the secondary beam are shown in Table 3-8 shown.
    Table 3-8 calculation of Flexural bearing capacity of normal Section of Beams
    4) Calculation of shear capacity of oblique section
    The calculation table for the shear capacity of the oblique section of the secondary beam is shown in Table 3-9. According to the -Regulations for Redistribution of Internal Forces-, when considering the redistribution of plastic internal forces, under uniform load, the calculated area of stirrups should be increased by 20% in the 1.05ho section from the support edge, and the pmin of the stirrups ?min 0.3ft/fw=0.159%.
    5) Design of anti-shear stirrups
    The calculation of the shear capacity of the oblique section of the secondary beam is shown in Table 3-9.
  6. Secondary beam reinforcement diagram
    The reinforcement diagram of the secondary beam is shown in Figure 3-12
    3.3.5 Main beam design
    The main beam is calculated according to the elastic theory, and the column section size is
    400mm×400mm.
  7. Load calculation
    1) Standard value of dead load
    The self-weight of the main beam is considered according to the concentrated load.
    Dead load from the secondary beam: 10.53×6.3=69.50(kN/m).
    Main fruit weight: 25×0.3× (0.75-0.08) ×2.4=12.06(kN/m).
    Plastering on the side of the main beam: 17×0.02× (0.75-0.08) ×2×2.4=1.09(kN/m).
    Load standard value: gk=82.65(kN/m).
    2) Standard value of live load
    According to Table D.0.1-1 of Appendix D of the -Load Code-, the standard value of live load is 5.00 for the main beam in metalworking workshops of four types.
    Combination value coefficient ?c. =1.0.
    The standard value of the live load from the board: 5.0×6.6×2.4=79.20(kN/m).
    3) Load sub-factor
    According to Article 3.2.4 of the -Load Code-, the value of the partial load factor is as follows.
    The constant load sub-factor is ?G; when it is unfavorable to the structure, it is 1.35; when it is favorable to the structure, it is 1.0.
    Live load sub-factor: standard value qk=5.00kN/m2 4.0kN/mm2, and the sub-factor is 1.3.
  8. Simple calculation
    The two ends of the beam in this project are integrally connected with the column, and the calculated span of each span is taken from the distance between the center lines of the support, calculated to the side span and the middle span: l0=lc =7200mm main beam calculation diagram is shown in Figure 3-13.
  9. Internal force calculation
    The three-span continuous beam shown in Figure 3-11 uses equations (3-12) and (3-13) to calculate the internal force of each control section, and calculate the standard value of the bending moment and the standard value of the shear force at each control section. Among them, the -coefficients in the table- are checked from the attached table 1-2 of the -Design of Concrete Structures-, and the most unfavorable arrangement of live loads is considered. The calculation results are shown in Table 3-10 and Table 3-11.

1) Calculation of standard value of bending moment
(1) Dead load
Bending moment within the span:
M1k=0.244gkl0=0.244×82.65×7200=145.20(kN·m) M2k=0.267gkl0=0.267×82.65×7200=158.89(kN·m) Bending moment of support:
MBk=-0.067gkl0=-0.067×82.65×7200=-39.87(kN·m)
Mcx=-0.267gkl0 =-0.267×82.65×7200=-158.89(kN·m)
(2) Live load
Bending moment within the span: M1t=0.289qkl0=0.289×79.20×7200=164.80(kN·m): M2z=0
Bending moment of support: MBk=Mck=-0.133gxl0=-0.133×79.20×7200=-75.84(kN·m)
2) Calculation of shear force standard value
(1) Dead load
VA=0.733gk =0.733×82.65=60.58(kN)
VB ?= =-1.267gk=-1.267×82.65 =-60.58(kN)
VB ?= gk =1×82.65=82.65(kN)
(2) Live load
VA=0.866qk=0.866×79.20=68.59(kN)
VB4=VB ? =-1.134qk=-1.134×79.20=-89.81(kN)
3) Perform internal force combination according to the following formula to obtain the most unfavorable combination design value at each control section
M =?GMGK +?Q?CMPK
V = ?G VGK + ?Q?CVpK
According to the static balance conditions, the most unfavorable internal force design values of the remaining sections are obtained. The results are shown in Table 3-10 and Table 3-11 shown.
4) Draw the internal force envelope diagram
Plot the combined bending moment design value and combined shear design value of each control section on the same coordinate diagram to obtain the internal force envelope diagram (Figure 3-14)
5) Calculation of the bearing capacity of the normal section of the main beam
The main beam support is calculated according to the rectangular section, and the mid-span section is calculated according to the T-shaped section.
According to Article 4.1.5 of the -Specification for Concrete-, the width bf of the flange of the T-shaped section is calculated, and the side span and the middle span are calculated according to the minimum value of l0/3 and (b+sn).
Side span: bf=min [l0/3, (b+sn)] =min [(7.2/3, (0.3+6.35)] =2.4m
Intermediate span: bf=min [l0/3, (b+sn)] =min [7.2/3, (0.3+6.3)] =2.4m
Take bf=2.40m, effective cross-section h0=750-65=685(mm) (double ribs), flange thickness hf=80mm, and get Mf=a1fcbfhf(h0-h f/2)=1.0×14.3×2400×80×(685-80/2)×10-6=1770.91(kN·m)
This value is greater than the design value of the mid-span bending moment of each span, so the mid-span section of each span belongs to the first type of T-shaped section.
The specific calculation parameters are as follows. C30 concrete: fc =14.3MPa; steel bar: longitudinal reinforcement fy=360MPa (HRB400)
If the longitudinal reinforcement is fyv=270MPa (HPB300), the calculation result of the flexural bearing capacity of the main girder is shown in Table 3-12.
6) Calculation of shear capacity of oblique section
The calculation of the shear capacity of the oblique section of the main beam is shown in Table 3-13. According to the -Internal Force Redistribution Regulations-, plasticity is considered
When the internal force is redistributed, under the action of concentrated load, in the section between the support margin and the nearest concentrated load, the calculated area of the stirrups should be increased by 20%, and the pmin 0.3ft/fyv=0.159% of the stirrups.
7) Additional transverse reinforcement
The design value of all the concentrated loads transmitted from the secondary beam to the main beam is

  1. Reinforcement diagram of main beam (Figure 3-15)
    ? Calculate the flexural bearing capacity of the front section according to the area of the actual longitudinal reinforcement. From the following formula, the main beams normal section resists the bending moment Calculation table (Table 3-14).
    ?Inversely calculate the bending bearing capacity of the front section according to the area of the actual longitudinal steel bars, and determine the material resisting bending moment diagram.
    ? According to the area of the longitudinal steel bars, divide the bending moment diagram into proportions, and draw the part borne by the bent steel bars on the outside.
    The main beam reinforcement diagram is shown in Figure 3-15.

GET SOLUTION FOR THIS ASSIGNMENT

CLICK HERE TO MAKE YOUR ORDER

TO BE RE-WRITTEN FROM THE SCRATCH

NO PLAGIARISM

  • Original and non-plagiarized custom papers- Our writers develop their writing from scratch unless you request them to rewrite, edit or proofread your paper.
  • Timely Deliverycapitalessaywriting.com believes in beating the deadlines that our customers have imposed because we understand how important it is.
  • Customer satisfaction- Customer satisfaction. We have an outstanding customer care team that is always ready and willing to listen to you, collect your instructions and make sure that your custom writing needs are satisfied
  • Confidential- It’s secure to place an order at capitalessaywriting.com We won’t reveal your private information to anyone else.
  • Writing services provided by experts- Looking for expert essay writers, thesis and dissertation writers, personal statement writers, or writers to provide any other kind of custom writing service?
  • Enjoy Please Note-You have come to the most reliable academic writing site that will sort all assignments that that you could be having. We write essays, research papers, term papers, research proposals. Prediction of beam and plate section dimensions

Get Professionally Written Papers From The Writing Experts 

Green Order Now Button PNG Image | Transparent PNG Free Download on SeekPNG Our Zero Plagiarism Policy | New Essays